Optional sequential shifter support (£5 extra )
Our SimRlink™ receiver now has added support for a sequential shifter if you choose this option
We now sell a sequential shifter, this is a PC shifter that we have converted to work with our SimRlink shifter box
https://simrtec.co.uk/sequential-shifter--simrlink-xbox--ps4--ps5--console-1128-p.asp
and if you want to make your own sequential shifter then all you need is our DIY box (same used with shifter above you only need 2 switches 1 for up shift one for down the rest is up to you
https://simrtec.co.uk/diy--simrlink-console-sequential-shifter-box-832-p.asp
Playstation 4/5* , PS4/PS5* MSB Pro+ wireless USB Plug and play handbrake using SimRlink
Works with all wheels Logitech G29 , G923 , Pro wheel , Thrustmaster and more
Handbrake will work on PS5 but only on PS4 version games
This version has the option of a progressive handbrake using left trigger input so 0 through 100% or button mode which uses the O button or the Square button when handbrake is pulled
PS5 handbrake Linked below
MSB Pro PS5 version (no Pro+ version currently)
How it works
Our handbrake operates as an extra controller with 3 modes , the modes are switched on the MSB module on handbrake
Progressive mode : switch down this outputs a variable value based on where the handbrake is through its travel so handbrake can be 35% , 50% , this gives more control of handbrake braking , this mode uses the left trigger input
Button mode : Switch up , this mode uses the O button and is on / off when red light is on handbrake is active , when red light is off handbrake is off
if you press the push button in this mode it will switch to using Square button instead of O button , then press it again and will be back to using O button
The Handbrake uses our SimRlink wireless technology to connect to the handbrake.
You get a SimRlink receiver + SimRlink handbrake the SimRlink receiver plugs into the PS4 USB port and communicates with the MSB SimRlink on the front of the handbrake
Wireless use requires 3 x AAA battery's *not supplied* a usb cable is also supplied
Games that we have tested and work with MSB Pro+ wireless handbrake SimRlink handbrake
Crew 2 | Crew Motorfest (Using Square button mode)
Grand Turismo 7
GT Sport
Dirt 2.0
DIRT 5
WRC Generations , 10 , 9
CarX Drift Racing
Need for speed heat (Use Square button mode)
Games that do not work
Assetto corsa (as far as we are aware it will not work)
Assetto corsa competizione
Programmable braking point (When MSB module switch is down)
Our new version MSB handbrake has a push button that you press to set your braking point from the braking point the MSB handbrake calculates the output from 100% (the chosen braking point) to 0 which is the rest position of the handbrake.
Click here for video showing how it works
Mounting options for handbrake
Universal Mount (£10)
Most sim setups / wheel stands can use the Universal mount
The Logitech shifter goes on top of this mount and the handbrake next to it
Playseat Evolution pro
if you have a gear shifter on the mount you will need the Universal mount but if you don't have one you can use our M6 2 bolt option and this puts the handbrake where the shifter would be and is only (£3 extra)
Playseat Challange / Playseat with out pro mount + £3
If you already have or are looking to purchase a mount for your Logitech shifter you can use the Universal mount with your playseat
with Playseat challenge you can also use a bar mount that bolts under the wheel this option requires you to buy the bar mount below and then the PSC mount from us , the PSC mount bolts directly to the bar below.
MUST BE THIS MOUNT BELOW
Click here for UK Playseat R.A.C.00168 Amazon link
Click here for USA Amazon link for mount
our mount will only fit this product from amazon choose PSC mount for this option
To fit this mount you need to remove the bolt and springs to gain access to the allen key bolts (M8) a 13mm spanner can do this this unwind take springs / washers off then fit part to mount then put back together.
Additional Desk Clamp Mount + £12
The Clamp mount has a full closure of about 150mm so if what you are clamping to is less that 15mm thick we will need to add a 3D printed spacer so please message us to let us know you need this option if required
if your option has not been added to shipping please email us
Contact Us
If you have any questions on how to return your item to us, contact us at simrtec@gmail.com
